Skip to content

Side Loader Forklifts: How They Work, Types and Training

Side loaders carry timber, pipe and steel lengthwise through aisles too narrow for a front-loading forklift with the same load. Here is how they work, the main types, and what OSHA requires before you drive one.

The short answer

A side loader forklift carries its forks on the side of the truck instead of the front. It picks up a load from beside it and travels with long loads, like timber, pipe, steel bar or sheet material, lying lengthwise along the truck. That lets it work in aisles and doorways too narrow for a front-loading forklift to turn in with the same load.

What is a side loader forklift?

A side loader forklift is a lift truck built for long loads. Its mast and forks sit on one side of the truck, roughly midway along it, and face sideways instead of forward. You will also see it written as sideloader forklift, side loading forklift, or side loader fork trucks. They all mean this design.

A pickup goes like this. The operator pulls up parallel to the load. The mast moves out sideways until the forks are under the load, the forks lift it clear, the mast pulls back in, and the forks lower the load onto the truck's deck. The truck then travels with the load resting on the deck, running the length of the truck. Putting it away is the same steps in reverse.

The operator sits in a cab at one end and drives in line with the load, not behind it. Because a long load runs along the truck instead of across the front, it adds little to the width the truck needs. That is why side loader forklift trucks exist: they get long goods through aisles and doorways a front-loading forklift could not use with the same load.

Top view of a counterbalance forklift carrying a long load across its forks A front-loading forklift drives along an aisle between two racks. The long load lies across the forks and sticks out past the racks on both sides. Counterbalance forklift Rack Rack Travel Long load sits across the forks Wider than the aisle Top view of a side loader carrying the same long load lengthwise A side loader drives along the same aisle. The long load rests on its deck, running along the length of the truck, and fits between the racks. The mast and forks are on the side of the truck. Side loader Rack Rack Travel Mast and forks Same load rides lengthwise on the deck Fits inside the aisle
Simplified top views, not to scale. Across the forks of a front-loading forklift, a long load is as wide as it is long. On a side loader the same load runs along the truck, so the aisle only has to fit the truck.

Types of side loader forklifts

Side loaders come in three broad kinds, split mostly by where they work:

  • Engine-powered yard side loaders. Diesel or propane trucks on large tires, built for outdoor stockyards: lumber yards, steel service centers, and pipe and tube yards. They move long bundles between outdoor racks and load and unload flatbed trailers.
  • Electric side loaders. Battery-powered trucks for indoor storage of long goods, working narrow aisles between racks of tube, bar, extrusions and sheet material. With no exhaust, they suit closed buildings.
  • Multi-directional (four-way) side loaders. Their wheels turn so the truck can drive sideways as well as forward. They pick up a long load across the forks, then travel sideways so it moves lengthwise down the aisle, and they can still handle pallets like an ordinary front-loading truck.

Turret trucks and reach trucks also save aisle space, but differently. A turret truck stays straight in a very narrow aisle and turns its forks to face the rack on either side. A reach truck stands on outriggers and pushes its forks forward into the rack. Both are mainly built for pallets stored high. A side loader is built for loads that are long rather than tall, and it carries them along its side.

What OSHA class is a side loader?

OSHA's own class list puts side loaders in Class II, electric motor narrow aisle trucks. The Powered Industrial Trucks eTool lists two side loader entries under Class II, "Side Loaders: Platforms" and "Side Loaders: High Lift Pallet," next to turret trucks and the reach truck. That fits the electric side loaders that work indoor narrow aisles.

OSHA's class list does not name engine-powered yard side loaders, and we will not guess a number for them. What matters is this: whatever its class, a side loader is a powered industrial truck. The forklift standard, 29 CFR 1910.178(a)(1), covers fork trucks, platform lift trucks, motorized hand trucks and other specialized industrial trucks powered by electric motors or engines. So the training rule in 1910.178(l) applies to every side loader, electric or engine, indoors or out.

Our 7 forklift classes guide maps everyday truck names to their OSHA class.

Do you need certification to operate a side loader?

Yes. Under 1910.178(l)(1)(ii), no one may operate a powered industrial truck, "except for training purposes," until they have completed the required training. That training has three parts under (l)(2)(ii): "formal instruction," "practical training," and "evaluation of the operator's performance in the workplace." The employer then certifies that the operator was trained and evaluated ((l)(6)) and repeats the evaluation at least once every three years ((l)(4)(iii)).

The training is tied to the type of truck. The first truck-related topic in (l)(3)(i)(A) is "operating instructions, warnings, and precautions for the types of truck the operator will be authorized to operate." Refresher training, which includes an evaluation ((l)(4)(i)), is required when "the operator is assigned to drive a different type of truck" ((l)(4)(ii)(D)). So an operator certified on a sit-down counterbalance forklift needs training and an evaluation on the side loader before driving it alone. Under (l)(5), topics already covered that still apply do not have to be repeated.

OSHA has said as much in writing. Its June 15, 1999 interpretation letter lists "an operator-up counterbalanced front/side loader truck" as a different type of truck from a sit-down counterbalanced rider truck, and says each type needs its own training and evaluation.

Our online course is the formal instruction: 8 lessons that take under an hour, then a 30-question exam with a pass mark of 80% and unlimited free retakes. It covers all seven forklift classes, and your certificate and wallet card download the minute you pass. The hands-on training happens at work on the side loader itself, and your employer signs the one-page evaluation form we include once you have shown you can run it safely.

Get Certified

Running side loaders in your yard?

Team seats cover the classroom part for every operator: $50 each for 2 to 4 operators, $40 for 5 to 9, and $30 for 10 or more, managed from one team dashboard. You run the hands-on training and evaluations on your own side loaders.

Certify Your Operators

What is different about driving a side loader forklift?

Mostly the geometry. These are the points a trainer covers when moving someone from a front-loading forklift to a side loader. They are good practice; OSHA paragraphs are cited where they apply.

  1. The load is beside you, not in front. You line up parallel to the stack instead of facing it, and judge fork position from the side. Getting the truck close and square before the mast goes out means less reaching. "Steering and maneuvering" is a required training topic ((l)(3)(i)(E)).
  2. Long loads swing and overhang. In a turn, the ends of a long load sweep a wide arc and can catch a rack upright, a parked vehicle or a person well away from your cab. Watch both ends, not only the truck, and keep people clear of the ends of the load. Slow down and sound the horn at cross aisles and anywhere your view is blocked ((n)(4)). Our pedestrian safety guide covers walkways and barriers.
  3. Travel with the load down on the deck. The load rides resting on the deck with the mast pulled in. The truck is least stable while the mast is out to the side with the load raised, so do that only when stopped at the pick or drop point, on level ground. If your truck has stabilizer legs, set them as the operator's manual directs before the mast goes out. Our stability triangle explainer shows how a load moved up and outward pulls the center of gravity toward the edge of the truck's base.
  4. Yard surfaces are uneven. Gravel, ruts and potholes tilt the truck, and a tilt toward the load side matters most with the mast out. OSHA lists "surface conditions where the vehicle will be operated" and "composition of loads to be carried and load stability" as required training topics ((l)(3)(ii)(A) and (B)).
  5. You see along the load, not over it. From a cab at one end, the far end of a long load is a long way off. "Visibility (including restrictions due to loading)" is a required topic ((l)(3)(i)(F)), and the driver must "look in the direction of, and keep a clear view of the path of travel" ((n)(6)). Where you cannot see, use a spotter and agreed hand signals.

Capacity rules do not change. Only loads within the truck's rated capacity may be handled ((o)(2)), and long loads that affect capacity must be adjusted ((o)(3)). Center a long bundle on the forks. The data plate rating applies at the load center printed on it; our load capacity calculator shows how safe capacity drops when the load center moves out.

Side loader vs counterbalance forklift

The counterbalance forklift is the all-rounder. The side loader is the specialist for long goods in tight space.

Counterbalance forklift Side loader
Where the forks are Front of the truck, facing forward Side of the truck, reaching out sideways
How a long load rides Across the forks, sticking out on both sides Lengthwise on the deck, along the truck
Loads it suits Pallets, crates and boxed goods Timber, pipe, steel bar, sheet material and other long goods
Aisle width needed Room to turn into the rack, plus the full length of a long load Little more than the truck's own width, since it never turns to face the rack
Where it is used Warehouses, loading docks, paved yards Lumber, steel and pipe yards, and indoor narrow-aisle storage of long goods
OSHA class Class I (electric) or IV and V (engine) Class II in OSHA's list; engine yard models are not named there

The two trucks are different types for training, so moving between them means training and an evaluation on the new one. For every rule that applies to both, see our OSHA forklift regulations guide.

Other truck types

Each of these is its own type with its own evaluation: reach truck certification, order picker certification (the operator rides up, so fall protection is added), electric pallet jack certification, and telehandler and rough terrain forklift certification. For the full map of truck types, see the 7 forklift classes.

Frequently asked questions

Is a side loader a forklift?
Yes. It lifts and carries loads on forks, so OSHA treats it as a powered industrial truck under 29 CFR 1910.178, the same legal category as every other forklift. OSHA's eTool lists side loaders among its Class II trucks.
Does a regular forklift certification cover a side loader?
Not on its own. Topics you were already trained in that still apply carry over under 1910.178(l)(5). A side loader is a different type of truck, so you need training on what differs, plus hands-on time and an evaluation on it, before you drive it alone (1910.178(l)(4)(ii)(D)).
Do I need a new evaluation to switch from an electric side loader to a diesel one?
Possibly. Engine or motor operation and refueling or battery charging are separate training topics, 1910.178(l)(3)(i)(D) and (K), so you need training on whatever differs before you drive it.
What is the difference between a side loader and a reach truck?
A reach truck stands on outriggers and pushes its forks forward into the rack, and it is built to stack pallets high. A side loader carries long loads along its side. Both are Class II trucks in OSHA's list, but they are different types for training. See our reach truck certification guide.
Can a side loader be used indoors?
Electric side loaders are built for it and have no exhaust. Engine-powered side loaders are mainly yard machines; indoors, the ventilation of the building matters, and OSHA lists closed environments with poor ventilation as a required training topic (1910.178(l)(3)(ii)(H)).
Can I get side loader certified online?
The classroom part, yes. The hands-on training and the evaluation have to happen on a side loader at your workplace, and your employer then certifies you.

Last updated:

More free forklift tools

See all resources

Get the Classroom Part Done Before Your Side Loader Training

OSHA-compliant online forklift training for $59, covering all seven classes. Under an hour, free retakes, certificate the minute you pass.

Get Certified