Skip to content

How to Operate a Forklift (Step by Step)

Forklift driving for beginners: one shift on a sit-down counterbalance forklift truck, from the pre-use check to parking it. Each step names the OSHA rule behind it where there is one.

The short answer

To operate a forklift, get trained and authorized first, check the truck before your shift, buckle the seatbelt, and travel with the forks low and tilted back. Pick up only stable loads within the capacity on the data plate, slow down and sound the horn at blind spots, never turn on a ramp, and park with the forks down, controls in neutral, power off and brake set.

Who is allowed to drive a forklift?

Only an operator the employer has trained, evaluated and authorized. OSHA makes the employer ensure every operator is competent to drive safely, shown by finishing the training and evaluation the rule sets out, 29 CFR 1910.178(l)(1)(i).

Not trained yet? Here is how to get forklift certified. The rest of this page is how to use a forklift, or fork truck, the way that training teaches it.

What do you do before driving a forklift?

Check the truck, get on safely, and buckle up.

  1. 1

    Do the pre-use check

    OSHA requires every truck to be examined before it is placed in service, at least daily, or after each shift where trucks run around the clock, 1910.178(q)(7). OSHA's eTool splits it into a visual check with the key off, seatbelt included, and an operational check with the engine running: brakes, steering, horn, lift and tilt. A truck that fails stays parked. Our forklift inspection checklist lists every item.

  2. 2

    Get on using three points of contact

    Many workplaces teach three points of contact: two hands and a foot, or two feet and a hand, on the truck at all times. OSHA's eTool adds: check your shoes for grease, grab the handhold, and never grab the steering wheel, which can turn under you. Get off the same way. Do not jump.

  3. 3

    Set the seat and mirrors, then buckle up

    Move the seat so you reach the pedals and levers without stretching, set any mirrors, and fasten the seatbelt before the truck moves. The seatbelt rule is not in 1910.178 itself: under an October 9, 1996 enforcement memo, OSHA requires employers to make operators use the seatbelt on any truck that has one. Our OSHA forklift regulations guide explains.

    If a sit-down truck ever starts to tip, OSHA's eTool says: don't jump, hold tight to the steering wheel, brace your feet and lean away from the impact.

What do the controls on a forklift do?

Learn them with the truck parked, before you move an inch. On a sit-down counterbalance forklift:

  • Steering wheel. Turns the rear wheels, so the back of the truck swings out wide on every turn.
  • Direction lever. Forward, neutral, reverse. Come to a full stop before you change direction.
  • Accelerator and brake. Speed and stopping, as in a car. Some trucks add an inching pedal for slow, fine moves near a load.
  • Lift lever. Raises and lowers the forks.
  • Tilt lever. Tilts the mast back to cradle a load, and forward to pick one up or set it down.
  • Side shift lever, if fitted. Slides the forks left or right without moving the truck.
  • Horn. Your warning at cross aisles and blind corners.
  • Parking brake. Holds the truck every time you get off.

Lever layouts differ between trucks, so read the labels on the one you drive. Our parts of a forklift guide has a labeled diagram and every pedal, lever and gauge.

How to drive a forklift: starting and moving off

Belt on, direction lever in neutral, foot on the brake, then start the truck, raise the forks just clear of the floor, tilt the mast back, and release the parking brake. Look all around, not only ahead, and move off slowly. OSHA requires the driver to "look in the direction of, and keep a clear view of the path of travel," 1910.178(n)(6).

Keep the forks low whether or not you are carrying anything. Raised forks put weight up high, where it tips the truck more easily, and OSHA's eTool warns that "even a small bump can cause a load to fall off elevated forks."

Forklift travel position: load low and tilted back, never raised Two side views of a sit-down forklift carrying a pallet. On the left, marked correct, the load sits just above the floor with the mast tilted back toward the operator. On the right, marked wrong, the load is raised high on the mast while the truck travels.

Travel like this: load just off the floor, mast tilted back.

Not like this: load raised while the truck moves.

How to pick up a load with a forklift

Check the load, line up square, get the forks all the way under, then lift and tilt back, as OSHA's load handling eTool teaches it.

  1. 1

    Check the load and its weight

    Handle "only stable or safely arranged loads," 1910.178(o)(1), and "only loads within the rated capacity of the truck," (o)(2). The capacity is on the data plate, which must be kept readable, (a)(6). A load that sits farther out on the forks lowers it; our load capacity calculator does the math.

  2. 2

    Approach slowly and square up

    Stop 8 to 12 inches in front of the load, square to it, and set the forks to the right height. The eTool says to raise or lower the forks only with the truck stopped and the brake set.

  3. 3

    Level the forks and drive in

    Level the forks, then drive in slowly until they are fully under the load and it rests against the carriage. OSHA requires the forks under the load "as far as possible," (o)(5). Keep the load centered between the forks.

  4. 4

    Lift, then tilt back

    Stop and set the brake, check overhead clearance, lift the load clear, then tilt the mast back slightly so the load rests against the load backrest extension. From a stack, the eTool says to lift about 4 inches above the stack below first.

  5. 5

    Look behind you and back out

    Check over both shoulders, back straight out slowly, stop, and lower the load to travel height.

How to drive a forklift with a load

Keep the load low and tilted back. Coming off a stack, the eTool says to lower the load until its lowest point is 6 to 8 inches from the floor and keep it at a safe travel height.

  • If the load blocks your view forward, drive in reverse with the load trailing, 1910.178(n)(4).
  • Slow down and sound the horn at cross aisles and anywhere your view is blocked, (n)(4).
  • Obey plant speed limits and stay about three truck lengths behind the truck ahead, (n)(1). Drive at a speed you can stop from, (n)(8), and slow down on wet or slippery floors, (n)(10).
  • Never drive up to anyone standing in front of a bench or other fixed object, (m)(1), and don't assume people on foot can hear your back-up alarm, OSHA's eTool warns. More in our forklift pedestrian safety guide.

On a ramp, keep the load uphill

On grades over 10 percent, OSHA's rule says "loaded trucks shall be driven with the load upgrade," 1910.178(n)(7)(i). On all grades, tilt the load back where applicable and raise it "only as far as necessary to clear the road surface," (n)(7)(iii). OSHA's eTool applies the same habit to every ramp: drive forward going up and in reverse coming down, so the load stays uphill both ways. With no load, the forks point downhill. And never turn on a ramp: the eTool warns a forklift "may tipover laterally on even a very small grade."

Which way a forklift faces on a ramp, loaded and empty Two forklifts on a ramp that rises to the left. On the left, a loaded forklift has its forks and load pointing uphill: it drives forward going up and in reverse coming down. On the right, an empty forklift has its forks pointing downhill. Uphill Uphill

Loaded: load faces uphill. Forward going up, reverse coming down.

Empty: forks face downhill. Never turn on the ramp.

Slope exaggerated. Source: 1910.178(n)(7) and OSHA's Powered Industrial Trucks eTool.

How to put a load down or stack it

Stop first, raise the load, creep in, then set it down level and back away with the forks lowered.

  1. 1

    Stop square to the spot

    Approach slowly, stop square to the rack or stack, put the direction lever in neutral and set the brake.

  2. 2

    Raise the load to height

    Check overhead clearance, then lift until the bottom of the load is just above where it will sit.

  3. 3

    Creep in slowly

    Your view is blocked once the load is up, so the eTool says to use the inching pedal to creep the load to the stack.

  4. 4

    Level and lower

    Tilt forward only when the load is over the rack or stack, 1910.178(o)(6), level it, and lower until it rests and the forks come free.

  5. 5

    Look behind, back out, lower the forks

    Check behind you, back straight out, stop, and lower the forks to just off the floor before you drive away.

How do you turn a forklift in tight spaces?

Slow down before the turn, then turn the wheel smoothly. OSHA requires speed reduced to a safe level for turns, turning the wheel "in a smooth, sweeping motion," 1910.178(n)(15).

Because the rear wheels steer, the back of the truck swings the opposite way from the turn. The eTool says to "anticipate the rear-end swing and start the turn as close to the inside corner as possible." Watch the tail, not just the forks.

Never turn with the forks raised, and never turn on a ramp. A raised load puts the weight high, and a sharp turn throws it sideways, which is how a forklift ends up on its side. Our stability triangle guide shows why.

How to park a forklift and shut it down

Before leaving a forklift unattended, lower the forks fully, put the controls in neutral, shut off the power and set the brakes, and block the wheels if it is on an incline, 1910.178(m)(5)(i). Unattended means you are 25 feet or more away, or you have left it and cannot see it, (m)(5)(ii).

OSHA's eTool adds: park on a hard, level surface in an authorized spot, tilt the mast forward slightly so the fork tips touch the floor, take the key, and keep clear of fire aisles, stairways and fire equipment. Stepping away but staying close? Our OSHA forklift regulations guide covers the rule for that case.

What mistakes do beginners make on a forklift?

The same handful, over and over:

  • Driving with the forks raised. OSHA's eTool: keep the load at a safe travel height, and never turn with the forks elevated.
  • Turning too fast. Reduce speed to a safe level for every turn, 1910.178(n)(15).
  • Forgetting the tail swing. The rear of the truck swings the opposite way from the turn, so watch the back end near racks and people.
  • Tilting forward with the load up. Tilt forward only when the load is over the rack or stack, (o)(6).
  • Reversing without looking. Look in the direction of travel, (n)(6).
  • Skipping the seatbelt. Buckle up before the truck moves, every time.

For the full list, with the accidents behind each rule, see our forklift safety rules.

Reading this does not make you a forklift operator

OSHA requires formal instruction, hands-on training and an evaluation in the workplace before anyone drives a forklift on their own, 1910.178(l)(1)(ii) and (l)(2)(ii).

Our online course is the formal instruction: 8 lessons, under an hour, all seven forklift classes, and a 30-question exam you pass at 80 percent, with unlimited free retakes. Your certificate and wallet card download the minute you pass. Your employer then trains you on your truck, signs the one-page evaluation form we include, and repeats the evaluation at least every three years.

Frequently asked questions

Is it hard to drive a forklift?
The driving itself is not hard. What takes practice is the rear-wheel steering, judging fork height, and keeping the truck smooth with a load on. That is why the hands-on training happens on the truck you will actually drive.
How long does it take to learn to operate a forklift?
The classroom part takes under an hour online. BLS says forklifts "may take only a few days to learn how to operate," and how long the hands-on part takes depends on your employer. See how long it takes to get forklift certified.
Is driving a forklift like driving a car?
The pedals feel similar, and that is where it ends. A forklift steers with its rear wheels, so the back swings out on every turn, and the load changes the balance: weight carried high or a sharp turn can tip a forklift in a way a car never would.
Can you operate a forklift without being certified?
Only as a trainee, under the direct supervision of someone qualified to train, where it endangers no one, 1910.178(l)(2)(i). Otherwise your employer is breaking OSHA's rule. See what happens if you drive a forklift without certification.
Do you need a driver's license to drive a forklift?
No. OSHA's forklift rule does not require a state driver's license, though some employers ask for one. More in do you need a license to drive a forklift?
How old do you have to be to drive a forklift?
18 for any job that is not on a farm, under federal child labor law. On a farm the minimum is 16. Details in our forklift age requirements guide.

Rule text from 29 CFR 1910.178 on osha.gov. Operating practice from OSHA's Powered Industrial Trucks eTool.

Last updated:

More free forklift tools

See all resources

Learn It Properly Before You Drive

Finish the classroom part of forklift certification online in under an hour, in English or Spanish. Your employer does the hands-on training and evaluation on your truck.

Get Certified

Training a crew? Certify your operators